Prohlížení Publikační činnost Katedry obrábění, montáže a strojírenské metrologie / Publications of Department of Working and Assembly (346) dle názvu
Zobrazují se záznamy 17-36 z 37
-
Heat distribution when nickel alloy grinding
(Tehnički vjesnik – Technical Gazette. 2012, vol. 19, no. 4, p. 947-951.) -
Hydroabrasive disintegration of rotating Monel K-500 workpiece
(The International Journal of Advanced Manufacturing Technology. 2018, vol. 96, issue 1-4, p. 981-1001.) -
Impact of cutting tool geometry on the dynamic load of system in the machining process of nickel Alloy 625
(Advances in Science and Technology Research Journal. 2016, vol. 10, issue 32, p. 24-31.) -
Increasing tool life during turning with a variable depth of cut
(Materiali In Tehnologije. 2013, vol. 47, issue 2, p. 199-203.) -
Influence of cutting parameters on heat-affected zone after laser cutting
(Tehnički vjesnik – Technical Gazette. 2013, vol. 20, no. 2, p. 225-230.) -
Influence of cutting speed on intensity of the plastic deformation during hard cutting
(Materiali In Tehnologije. 2013, vol. 47, issue 6, p. 745-755.) -
Influence of focusing tube wear on vibrations and surface roughness
(Tehnički vjesnik – Technical Gazette. 2015, vol. 22, no. 2, p. 271-278.) -
Influence of tool wear on the mechanism of chips segmentation and tool vibration
(Tehnički vjesnik – Technical Gazette. 2013, vol. 20, no. 1, p. 105-112.) -
Investigating the influence of cutting speed on the tool life of a cutting insert while cutting DIN 1.4301 steel
(Materiali In Tehnologije. 2016, vol. 50, issue 3, p. 439-445.) -
Mechanisms of cutting blade wear and their influence on cutting ability of the tool during machining of special alloys
(Advances in Science and Technology Research Journal. 2016, vol. 10, issue 31, p. 144-150.) -
New way to take control of a structural grain size in the formation of nanomaterials by extrusion
(Materialwissenschaft und Werkstofftechnik. 2012, vol. 43, issue 5, p. 405-411.) -
Prediction of the catastrophic tool failure in hard turning through acoustic emission
(Materiali In Tehnologije. 2015, vol. 49, issue 3, p. 355-363.) -
Properties and comparison of PVD coatings
(Tehnički vjesnik – Technical Gazette. 2016, vol. 23, no. 2, p. 569-574.) -
Rationalization of manufacturing of plastic injection moulds by abrasive waterjet
(Tehnički vjesnik – Technical Gazette. 2015, vol. 22, no. 2, p. 521-525.) -
Secondary hardening of low-alloyed creep-resistant steel welds
(Metalurgija. 2014, vol. 53, no. 1, p. 25-28.) -
Tangential turning of Incoloy alloy 925 using abrasive water jet technology
(The International Journal of Advanced Manufacturing Technology. 2016, vol. 82, issue 9-12, p. 1747-1752.) -
Techno-economical comparison of cutting material by laser, plasma and oxygen
(Tehnički vjesnik – Technical Gazette. 2012, vol. 19, no. 4, p. 813-817.) -
Testing ceramics inserts at irregular interrupted cut on material 14MoV6
(Engineering Review. 2017, vol. 37, no. 1, p. 67-73.) -
Testing of Greenleaf ceramic cutting tools with an interrupted cutting
(Tehnički vjesnik – Technical Gazette. 2011, vol. 18, no. 3, p. 327-332.) -
The effect of feed rate on durability and wear of exchangeable cutting inserts during cutting Ni-625
(Tehnički vjesnik – Technical Gazette. 2017, vol. 24, suppl. 1, p. 1-6.)