Procházení Fakulta strojní / Faculty of Mechanical Engineering (FS) dle data vydání

Comparison of different FETI preconditioners for elastoplasticity

Čermák, Martin; Hapla, Václav; Kružík, Jakub; Markopoulos, Alexandros; Vašatová, Alena (Computers & Mathematics with Applications. 2017, vol. 74, issue 1, p. 96-109.)

Testing ceramics inserts at irregular interrupted cut on material 14MoV6

Čep, Robert; Kyncl, Ladislav; Malotová, Šárka; Petrů, Jana; Zlámal, Tomáš; Czan, Andrej (Engineering Review. 2017, vol. 37, no. 1, p. 67-73.)

Effect of chip breakers on the cutting force during the machining of steel C45

Kratochvíl, Jiří; Petrů, Jana; Pagáč, Marek; Holubják, Jozef; Mrázik, Jozef (Advances in Science and Technology Research Journal. 2017, vol. 11, issue 1, p. 173-178.)

The effect of the number of conveyor belt carrying idlers on the failure of an impact place: A failure analysis

Honus, Stanislav; Bocko, Peter; Bouda, Tomáš; Ristović, Ivica; Vulić, Milivoj (Engineering Failure Analysis. 2017, vol. 77, p. 93-101.)

Capacities and limitations of wind tunnel physical experiments on motion and dispersion of different density gas pollutants

Zavila, Ondřej; Blejchař, Tomáš (Measurement Science Review. 2017, vol. 17, issue 2, p. 53-60.)

Inovace a vývoj periferních zařízení robotů a manipulátorů pro aplikace v oblasti bezpečnosti a ochrany obyvatel a záchranných systémů

Kopec, Petr (Disertační práce, 2017)

Detection of grinding burn through the high and low frequency Barkhausen noise

Mičietová, Anna; Neslušan, Miroslav; Čep, Robert; Ochodek, Vladislav; Mičieta, Branislav; Pagáč, Marek (Tehnički vjesnik – Technical Gazette. 2017, vol. 24, suppl. 1, p. 71-77.)

Simulation of laboratory tests of steel arch support

Horyl, Petr; Šňupárek, Richard; Maršálek, Pavel; Pacześniowski, Krzysztof (Archives of Mining Sciences. 2017, vol. 62, issue 1, p. 163-176.)

High density poly(ethylene)/CaCO3 hollow spheres composites for technical applications

Lapčík, Lubomír; Maňas, David; Vašina, Martin; Lapčíková, Barbora; Řezníček, Martin; Zádrapa, Petr (Composites Part B: Engineering. 2017, vol. 113, p. 218-224.)

The effect of feed rate on durability and wear of exchangeable cutting inserts during cutting Ni-625

Petrů, Jana; Zlámal, Tomáš; Čep, Robert; Sadílek, Marek (Tehnički vjesnik – Technical Gazette. 2017, vol. 24, suppl. 1, p. 1-6.)

A method for predicting ratcheting and wear in rolling contact fatigue, taking technological residual stresses into consideration

Halama, Radim; Šofer, Michal; Rojíček, Jaroslav; Fojtík, František; Kolařík, Kamil (Tehnički vjesnik – Technical Gazette. 2017, vol. 24, suppl. 1, p. 7-14.)

Improvement of mechanical and electrical properties of rotary swaged Al-Cu clad composites

Kocich, Radim; Kunčická, Lenka; Macháčková, Adéla; Šofer, Michal (Materials & Design. 2017, vol. 123, p. 137-146.)

Analysis of the vibration attenuation of rotors supported by magnetorheological squeeze film dampers as a multiphysical finite element problem

Ferfecki, Petr; Zapoměl, Jaroslav; Kozánek, Jan (Advances in Engineering Software. 2017, vol. 104, p. 1-11.)