Browsing Publikační činnost Katedry obrábění, montáže a strojírenské metrologie / Publications of Department of Working and Assembly (346) by Issue Date
Now showing items 1-20 of 288
-
Chip formation analysis during hard turning
(Strojarstvo. 2008, vol. 50, no. 6, p. 337-346.) -
Testing of Greenleaf ceramic cutting tools with an interrupted cutting
(Tehnički vjesnik – Technical Gazette. 2011, vol. 18, no. 3, p. 327-332.) -
Aspects of using tool axis inclination angle
(Strojniški vestnik - Journal of Mechanical Engineering. 2011, vol. 57, no. 9, p. 681-688.) -
Deformations after heat treatment and their influence on cutting process
(Tehnički vjesnik – Technical Gazette. 2011, vol. 18, no. 4, p. 601-608.) -
Cutting tool life tests of ceramic inserts for car engine sleeves
(Tehnički vjesnik – Technical Gazette. 2011, vol. 18, no. 2, p. 203-209.) -
Factor analysis of the abrasive waterjet factors affecting the surface roughness of titanium
(Tehnički vjesnik – Technical Gazette. 2011, vol. 18, no. 1, p. 73-77.) -
Heat distribution when nickel alloy grinding
(Tehnički vjesnik – Technical Gazette. 2012, vol. 19, no. 4, p. 947-951.) -
Techno-economical comparison of cutting material by laser, plasma and oxygen
(Tehnički vjesnik – Technical Gazette. 2012, vol. 19, no. 4, p. 813-817.) -
New way to take control of a structural grain size in the formation of nanomaterials by extrusion
(Materialwissenschaft und Werkstofftechnik. 2012, vol. 43, issue 5, p. 405-411.) -
A new method for the prediction of laser cut surface topography
(Measurement Science Review. 2012, vol. 12, issue 5, p. 195–204.) -
Influence of tool wear on the mechanism of chips segmentation and tool vibration
(Tehnički vjesnik – Technical Gazette. 2013, vol. 20, no. 1, p. 105-112.) -
Influence of cutting parameters on heat-affected zone after laser cutting
(Tehnički vjesnik – Technical Gazette. 2013, vol. 20, no. 2, p. 225-230.) -
Experimental testing of exchangeable cutting inserts cutting ability
(Tehnički vjesnik – Technical Gazette. 2013, vol. 20, no. 1, p. 21-26.) -
Increasing tool life during turning with a variable depth of cut
(Materiali in Tehnologije. 2013, vol. 47, issue 2, p. 199-203.) -
Comparison of non-traditional technologies for material cutting from the point of view of surface roughness
(The International Journal of Advanced Manufacturing Technology. 2013, vol. 69, issue 1-4, p. 81-91.) -
Experimental tool life tests of indexable inserts for stainless steel machining
(Tehnički vjesnik – Technical Gazette. 2013, vol. 20, no. 6, p. 933-940.) -
Influence of cutting speed on intensity of the plastic deformation during hard cutting
(Materiali in Tehnologije. 2013, vol. 47, issue 6, p. 745-755.) -
Cutting tool wear monitoring with the use of impedance layers
(Tehnički vjesnik – Technical Gazette. 2014, vol. 21, no. 3, p. 639-644.) -
Secondary hardening of low-alloyed creep-resistant steel welds
(Metalurgija. 2014, vol. 53, no. 1, p. 25-28.) -
Evaluation of creep properties of steel P92 and its welded joint
(Metalurgija. 2014, vol. 53, no. 2, p. 175-178.)