| dc.contributor.author | Hreha, Pavol | |
| dc.contributor.author | Hloch, Sergej | |
| dc.contributor.author | Valíček, Jan | |
| dc.contributor.author | Monková, Katarína | |
| dc.contributor.author | Monka, Peter | |
| dc.contributor.author | Harničárová, Marta | |
| dc.contributor.author | Fusek, Martin | |
| dc.contributor.author | Konjatić, Pejo | |
| dc.date.accessioned | 2011-03-11T08:57:39Z | |
| dc.date.available | 2011-03-11T08:57:39Z | |
| dc.date.issued | 2010 | |
| dc.identifier.citation | Tehnički vjesnik – Technical Gazette. 2010, vol. 17, no. 4, p. 475-480. | en |
| dc.identifier.issn | 1330-3651 | |
| dc.identifier.uri | http://hdl.handle.net/10084/84350 | |
| dc.description.abstract | The article deals with the impact of mass flow rate of abrasive in a water jet when penetrating into a material by using the vibration analysis. The vibrations of material were recorded by sensors placed on the experimental material.Values that were studied were amplitude and FFT (Fast FourierTransform) spectrum of
signal. The stainless steel AISI309 was used as the experimental material. Data recorded during the cutting process of theAWJ cutting were analysed by the
LabVIEWprogramming environment. The paper outlines the course of the recorded data and the FFTspectrum of this signal. Presented here is only a part of the
basic research focused on the application of vibrations as a feedback for on-line control of abrasive water jet. | en |
| dc.format.extent | 613076 bytes | cs |
| dc.format.mimetype | application/pdf | cs |
| dc.language.iso | en | en |
| dc.publisher | Sveučilište J.J. Strossmayera u Osijeku. Strojarski fakultet | en |
| dc.relation.ispartofseries | Tehnički vjesnik – Technical Gazette | en |
| dc.relation.uri | http://hrcak.srce.hr/file/94277 | en |
| dc.subject | abrasive water jet | en |
| dc.subject | abrasive mass flow rate | en |
| dc.subject | penetration into material | en |
| dc.subject | vibration analysis | en |
| dc.title | Impact of abrasive mass flow rate when penetrating into a material on its vibration | en |
| dc.title.alternative | Utjecaj brzine abrazivnog masenog protoka na vibracije kod prodiranja u materijal | en |
| dc.type | article | en |
| dc.identifier.location | Není ve fondu ÚK | en |
| dc.description.abstract-en | Članak se bavi utjecajem masenog protoka u vodenom mlazu, kada on prodire u materijal, koristeći analizu vibracija. Vibracije materijala zabilježene su
senzorima postavljenim na eksperimentalnom materijalu. Veličine koje su proučavane su amplituda i FFT
je nehrđajući čelik AISI 309. Podaci snimljeni tijekom procesa rezanja
sadrži djelomični rad temeljn
(brza Fourierova transformacija) spektar signala.
Kao eksperimentalni materijal korišten mlazom vode analizirani su LabVIEW
programskim okruženjem. Nadalje ovdje je opisan tok snimljenih podataka i FFT spektar ovog signala. Izvještaj og istraživanja
usmjerenog na primjenu vibracija kao povratne informacije za on-line kontrolu abrazivnog vodenog mlaza. | en |
| dc.rights.access | openAccess | |
| dc.type.version | publishedVersion | |
| dc.identifier.wos | 000286449300011 | |