Zobrazit minimální záznam

Comparison of surface roughness quality created by abrasive water jet and CO2 laser beam cutting

dc.contributor.authorZeleňák, Michal
dc.contributor.authorValíček, Jan
dc.contributor.authorKlich, Jiří
dc.contributor.authorŽidková, Petra
dc.date.accessioned2012-11-12T09:10:47Z
dc.date.available2012-11-12T09:10:47Z
dc.date.issued2012
dc.identifier.citationTehnički vjesnik – Technical Gazette. 2012, vol. 19, no. 3, p. 481-485.cs
dc.identifier.issn1330-3651
dc.identifier.urihttp://hdl.handle.net/10084/95697
dc.description.abstractThis paper deals with an evaluation of the surface roughness quality created by abrasive water jet and by CO2 laser, in terms of influence of the selected technological parameters on the final quality of machined surfaces. The main objective of these experimental studies was to consider the use of both technologies for cutting of difficult to cut materials. Experiments presented in the paper were carried out on titanium ASTM B265-99 samples. The machined surfaces of samples were measured by an optical profilometer. Subsequently, selected topographical characteristics were studied. The obtained data were used for comparison of surface roughness parameters Ra in different depths. Based on achieved results the comparison of both technologies was made.cs
dc.format.extent3245757 bytescs
dc.format.mimetypeapplication/pdfcs
dc.language.isoencs
dc.publisherSveučilište J.J. Strossmayera u Osijeku. Strojarski fakultetcs
dc.relation.ispartofseriesTehnički vjesnik – Technical Gazettecs
dc.relation.urihttp://hrcak.srce.hr/file/129054cs
dc.subjectabrasive waterjet cuttingcs
dc.subjectCO2 laser beam cuttingcs
dc.subjectoptical profilometrycs
dc.subjecttitanium samplecs
dc.subjectrezanje abrazivnim vodenim mlazomcs
dc.subjectrezanje CO2 laserskim zrakamacs
dc.subjectoptička profilometrijacs
dc.subjecttitanski uzorakcs
dc.titleComparison of surface roughness quality created by abrasive water jet and CO2 laser beam cuttingcs
dc.title.alternativeUsporedba kvalitete hrapavosti površine ostvarene rezanjem abrazivnim vodenim mlazom i CO2 laserskim zrakamacs
dc.typearticlecs
dc.identifier.locationNení ve fondu ÚKcs
dc.description.abstract-enOvaj se rad bavi procjenom kvalitete površinske hrapavosti ostvarene abrazivnim vodenim mlazom i CO2 laserom, s obzirom na utjecaj odabranih tehnoloških parametara na završnu kvalitetu obrađenih površina. Glavni cilj ovih eksperimentalnih istraživanja bio je razmotriti uporabu obje tehnologije za rezanje materijala koji se teško režu. Eksperimenti prezentirani u radu provedeni su na uzorcima titana ASTM B265-99. Obrađene površine uzoraka mjerene su optičkim profilometrom. Nakon toga, proučene su odabrane topografske značajke. Dobiveni podaci su korišteni za usporedbu hrapavosti površina parametara Ra u različitim dubinama. Napravljena je usporedba obje tehnologije na temelju postignutih rezultata.cs
dc.rights.accessopenAccess
dc.type.versionpublishedVersioncs
dc.type.statusPeer-reviewedcs
dc.description.sourceWeb of Sciencecs
dc.description.volume19cs
dc.description.issue3cs
dc.description.lastpage485cs
dc.description.firstpage481cs
dc.identifier.wos000309164400003


Soubory tohoto záznamu

Název:
TEH-VJESN-2012-19-3-481-zelenak.pdf
Velikost:
3.095Mb
Formát:
PDF
Popis:
publishedVersion
Zobrazit/otevřít

Tento záznam se objevuje v následujících kolekcích

Zobrazit minimální záznam